Shake or Stir Before Using
Brick Water Repellent is an architectural grade product that meets all industry guidelines for selection of commercial water repellents for masonry. This high performance penetrating siloxane bonds with the minerals in brick and concrete to provide long-lasting water repellency. MasonrySaver is breathable, non-film forming, and will not alter surface color or appearance.  See Product Data Sheet for performance tests.

DIRECTIONS FOR USE:
Surface and air temperatures should be a minimum of 40°F. Do not use on asphalt-based material and surfaces. Do not apply to frozen or frost covered surfaces.  Application must be clean, sound, dry to slightly damp surfaces. Do not apply to wet or water saturated surfaces, or when rainfall is expected within six hours.

Surface Preparation: Remove dust, dirt, grease, oils, efflorescence, wax, curing compounds, coatings or other foreign matter that might block or interfere with product penetration. See Product Data Sheet for acceptable cleaning methods.

Cure new masonry and concrete a minimum of twenty eight days, and at least three days after repairs or tuckpointing before applying MasonrySaver. Make necessary repairs including: structural cracks, faulty roofing, coping, flashings, expansion joints, mortar joints and sealants. Test a small area of surface before starting general application to assure desired results and coverage rates.  Provide adequate ventilation if applied indoors.

Application Vertical: Apply from bottom up using a low pressure sprayer (10-25 psi) with a fan type nozzle, or by roller with a minimum 3/8in nap. Flood surface until excess runs down six to eight inches below spray or roller pattern. To assure optimum performance a wet on wet application is recommended; apply second coat within three to five minutes.  A wet treated surface may be agitated with a soft bristle brush to ensure even distribution and greater penetration. Protect adjacent paint films, windows, plant life, asphalt-based material and all non-targeted surfaces from overspray.  Remove overspray immediately with soap and water.

Application Horizontal: Apply a single application with low pressure spray or pour from container so that surface remains wet for two to three minutes before final absorption.  Avoid puddling or ponding; brush or broom to spread material until it thoroughly penetrates the surface.  Block all drains and use absorptive coverings to contain runoff of excess material.  Use soap and water to remove overspray as soon as possible.

Caution:  Over application of material may cause darkening of surface.

Drying Time - One to two hours depending on temperature and humidity.

Clean Up - Thoroughly rinse spray equipment with clean water. Clean rollers with soap and water. Rinse thoroughly.

Storage and Disposal- Do not store below 32°F. Dispose of this container and any unused product in accordance with all federal, state and local regulations.

Helpful Tips: Protect surrounding vegetation. Wet leaves and greenery before and after application or cover with plastic. Asphaltic material may be damaged if soaked. Protect from run-off with drop cloths or other absorbent material.  Most oil based paints may be applied over MasonrySaver after a twenty-four hour drying period.  Pre-test a small area for compatibility.

Technical Assistance: 800-860-6327

Caution: Accumulation of product on ladders, scaffolding, roofing, etc. may result in a slippery surface. Prevent overspray from accumulating. Clean surfaces as necessary.

LIMITED 5 YEAR DURABILITY WARRANTY
Our recommendations for use of this product are based upon testing believed to be reliable. Since field conditions vary widely, the user must determine the suitability of the product for the particular use and specific method(s) of application.  SaverSystems water repellent will exhibit a water repellant effect for five years from the date of application if applied according to label instructions and if minimum application requirements are met.

This warranty does not cover pre-existent flaking, spalling, abrading, faulty construction and/or other defects which might erode treated surfaces.  If water repellent fails to perform as specified, SaverSystems will furnish, as the sole remedy, enough water repellent to correct the condition.  This warranty does not include labor, or the cost of labor for the re-application of water repellent.  Neither seller nor manufacturer shall be liable for loss or damage, direct, incidental or consequential, regardless of the legal theory asserted, including negligence and/or strict liability.

Coverage Guidelines:
Actual coverages will very due to porosity of surface materials.

Do Not Thin Product.
 

SaverSystems, division of Meredith, inc.
1751 Sheridan St.
Richmond, IN 47374

Non-photochemically reactive
Maximum V.O.C. 50 gr./lt. (.422 lbs. per/gal.)

Cautions: Keep out of reach of children. Do not take internally. Keep from freezing.

First Aid: if swallowed, drink milk or water; do not induce vomiting. Call physician immediately. For skin contact: wash thoroughly with soap and water; if irritation persists, get medical attention.

For eye contact Flush immediately with water, then remove any contact lenses. Continue to flush eyes with water for at least fifteen minutes. See Product Data Sheet and MSDS sheet for additional information on this product.

purchase MasonrySaver